Category Archives: By Manufacturer

OEM Original Diagnostic Coding Programming software technics sharing for BMW Mercedes Audi Porsche Land Rover Tesla Ferrari and more.

Explaining the Differences Between USB and Enet BMW Coding

BMW coding

Explaining the Differences Between USB and Enet Cable BMW Coding iDrive Owning a BMW isn’t just about getting from point A to point B in luxury (though that’s a big plus), it’s also about a way of life. Although BMW manages to package a sleek and sexy package with tons of amazing features right off […]

BMW Coding Options for i Chassis i3 & i8

bmw i8 coding options

BMW Coding Options for I Chassis Applicable Models 2014 – Present I01 i3 Battery Electric Vehicle (BEV) & Range Extender (REX) 2014 – Present I12 i8 Coupe 2018 – Present I15 i8 Roadster iDrive/Infotainment Features Remove Start-up and Camera Legal Disclaimers Change Start-up Logo to M Logo Change Warning Chimes / PDC Sounds to BMW […]

BMW Coding Options for G Series

BMW MGU ID7

BMW Coding Options for G Series Applicable Models 2 Series   F44  228i, M235i (FWD & xDrive Models) 3 Series   G20  330i, 330e, M340i  (RWD & xDrive Models) 5 Series   G30/F90  530i, 530e, 545e, 540i , M5 (RWD & xDrive Models) 6 Series   G32  640i Gran Turismo (RWD & xDrive Models) 7 Series   G11/G12    740i, […]

E-sys BMW Coding for F18 Full LCD Instrument 6WB Retrofit

Mini Cooper JCW crystal instrument cluster

This video demonstrates how to use BMW E-sys and BMW Esysplus to do coding on BMW configuration. This example shows a BMW F18 NBT full LCD instrument retrofit with reverse image 3AG. LCD Full Code: Unit:609,6NL,6NR 6WB NBT 3AG Procedures for Reverse Image: Read through the original FA. Click “Read” and save it, then click […]

How to Change BMW E Series firmware iLevel by TOOL32?

Change-BMW-E-Series-Vehicle-Integrierte-Level-by-TOOL32-2

This post will walk you through changing the integrated level on a BMW E series vehicle using TOOL32. Load a FRM or CAS file, for example, FRM70.PRG, into the TOOL32 software. Choose “i stufe lesen,” and then read out the integrated level I-STEP for the current vehicle. https://www.car-auto-repair.com/wp-content/uploads/2021/02/Change-BMW-E-Series-Vehicle-Integrierte-Level-by-TOOL32-1.jpg Choose “i stufe schreiben” Then enter the […]

How to coding the Head Unit Screen Display on a BMW EVO?

Coding-for-BMW-EVO-Head-Unit-Screen-Upgrade-2

After converting a BMW EVO head unit from small to large screen, you must code the value to make it valid. So, in this guide, I will show you how to use E-sys to upgrade the screen on your BMW EVO head unit from 6.5″ to 8.8-10.2″. Procedures: Connect ENET cable on BMW obd port, […]

How To Replace BMW F/G Series DME/DDE

How To Replace BMW F/G Series DME/DDE

In the case of F series, you can use ISN factory mode to read ISN and swap the ISN stored in DME. Some DMEs (Gasoline models) in F series support changing read ISN by OBD mode itself up to 2012 models in that case you can try to replace ISN from original to donor ECU […]

How to Setup BMW ISTA for Use with BMW ICOM?

BMW ISTA ICOM Next setup

The goal of this post is to assist DIYers or in-house technicians in configuring BMW Rheingold ISTA with BMW ICOM. You can also use BMW K+DCAN or BMW ENET or Enet WiFi Adapter to run the BMW Rheingold ISTA software. BMW ICOM Configuration Procedures with BMW ISTA Navigate to the properties of the network adapter […]

A guide to Setup BMW ISTA with K+DCAN Configuration

How to Setup BMW ISTA K+DCAN Configuration

This article will walk you through the process of configuring and verifying ISTA+ to work with BMW K+DCAN cable. Furthermore, the following information is freely available on the internet. The information below is freely available on the internet, but it has been consolidated here to assist the DIYer in interface configuration (Rheingold, ISTA-D, and ISTA+ […]

How to Setup BMW ISTA Using a BMW ENET Cable?

how to Setup BMW ISTA Using a BMW ENET Cable

Here is a guide for configuring BMW Rheingold ISTA with BMW ENET cable or Enet WiFi adapter. Because the ENET cable costs less than $10, it is highly recommended for the individual DIYer. And we hope you find this guide useful. Step-by-step Configuration of ISTA with BMW ENET cable: Open the properties of the network […]

How to Make Use of BMW ISTA for Programming and Coding?

for BMW ISTA for Programming and Coding

What exactly is BMW Rheingold ISTA? ISTA is a workshop system that contains data and information from BMW AG. ISTA is an acronym that stands for Integrated Service Technical Application.  BMW used DIS (Diagnostics Information System) during the initial development of this tool, and as the programs evolved and due to the nature of BMW’s file naming conventions, the workshop system became known as Rheingold in the enthusiast world.  Rheingold is the folder that houses the main application and data. Rheingold was renamed ISTA-D (D stands for Diagnostics),  and BMW’s programming application (not covered in this document) used the same nomenclature, ISTA, but with a P (for programming) or ISTA-P. ISTA+ PROGRAMMING is only for F, G, and I Series, Mini, and Rolls Royce cars ISTA-P will be to program E-series only and ISTA+ will program everything else. ISTA+ programming with Enet or Enet WiFi adapter WILL NOT work! ICOM Next A  is required! BMW Rheingold ISTA Functions […]

Select the fields to be shown. Others will be hidden. Drag and drop to rearrange the order.
  • Image
  • SKU
  • Price
  • Stock
  • Availability
  • Add to cart
  • Description
  • Content
  • Additional information
  • Attributes
Click outside to hide the compare bar
Compare